Delhi
Delhi
Ghaziabad
Germany
+91 9899772424 Mon - Sat 10:00 - 20:00 712 GT Road Shahdara Delhi
+91 9899335858 Mon - Sat 10:00 - 20:00 27D Anand Industrial Area, Ghaziabad UP
+49 1590 8635842 Mon - Fri 09:00 - 17:00 Kerpenerstrasse 71, 50937, Cologne, Germany
Ceritified
ISO 9001:2015
The Best
#1 Delhi NCR
Most Reliable
Supplier in region
Get A Quote

How to Read a Busbar Drawing: Dimensions, Holes, Bends & Specs (A Custom Busbar Manufacturer in India Explains)

 

A panel builder sends a busbar drawing to a manufacturer. Two weeks later they receive the busbars, but they are all out by 2mm. No one is happy. Usually the manufacturer isn’t at fault, nor is the drawing. Someone has just interpreted it incorrectly.

By understanding how to read a drawing when purchasing or designing customized busbars, it will save you money, rework, and lots of angry emails. This guide will walk you through how to do this, just like a custom busbar manufacturer in India would explain on the shop floor.

Whether you are a panel builder, electrical designer, or procurement, your goal is to get the right-sized busbar. We will take you step by step through how to read the drawing. If you have found this page whilst searching for how to calculate the size of busbars or current ratings, we will also show you how this is calculated and where it comes into play on the drawing.

What Is A Busbar Drawing?

A busbar drawing is a 2D technical drawing that will give the manufacturer precise details of how to cut, punch, bend, and finish your busbar. It will include dimensions, hole locations, bending angles, material grade, surface finishes, and tolerances.

It is an agreement between you and your customized copper & aluminum busbar manufacturer. Anything not included in the drawing can be open to interpretation.

Why It Matters More Than You’d Think?

 Busbars carry large amounts of current, so small errors can cause major issues:

  • Misaligned holes will cause forcing of components and stressed joints.

  • Incorrect bend radius can cause cracking of the material or reduced section.

  • Poor contact will cause heating, which will result in failures.

  • The busbar will have to be reworked, causing delays to your entire panel or switchgear.

  • Having a clear drawing will give you faster, more accurate quotes.

In a switchgear panel there is usually very little room for maneuver. Busbars have to be cut, punched, and bent to fit into tight areas. This means if there is any ambiguity in the drawing, it can cause delays to your entire dispatch.

Step by Step: Reading a Busbar Drawing

1. Title Block

Look at the block in the corner of the drawing. This will usually show:

  • Part Number & Revision (Always make sure you are using the correct revision.)

  • Material (Cu-ETP Copper, 6101, 1200 Aluminum Alloy, etc.)

  • Temper / Grade

  • Surface finish (tinned, silver, nickel, etc.)

  • Tolerance & Standard

  • Quantity & Unit (Typically MM)

Common reasons for scrap are incorrect revisions, so make sure you check this first.

Quick tip: Make sure that the part number & revision in the title match your purchase order & quote.

2. Cross section

The size of the busbar will be written in the format Width x Thickness (e.g., 50 x 10 mm). This will determine how much current it can carry. If you alter the thickness to make it easier to bend, this has altered your electrical design.

It will also affect how well it can dissipate the heat. This should be determined by your electrical design.

If you’re wondering how you calculate the size of the busbar for your panel, the basic principle is to divide the current by current density to achieve the cross-sectional area. Current density will depend on the material, ambient temperature, enclosure type, and temperature rise allowed. For example, a 400 amp busbar will be different in copper vs. aluminum and open air vs. closed panel. A busbar sizing chart is a good starting point; however, your final calculation should always be compared to your design standard.

3. Overall Dimensions

Look out for the developed length and finished dimensions. These are two different measurements and a common mistake.

  • Developed Length—The length of the bar in its raw form.

  • Leg Lengths—The distance between bends.

  • Overall – The final size of the bar.

If the drawing only shows the finished size, ask your manufacturer for the developed length. This is a 2-minute check that can prevent an entire batch from being too short.

4. Check the Holes

Holes are often a source of contention. A good drawing will show:

  • Hole Size (M8, M10, M12 clearance, etc.)

  • Hole Shape (Circular or Slot/Oblong)

  • Hole Pitch (Distance between centers of holes)

  • Edge Distance (Distance between center of hole & edge of busbar)

  • Reference (where measurements are taken from)

Be aware of how the holes are dimensioned. If dimensioned from a baseline (all hole measurements from one datum), this will help prevent tolerance buildup. If dimensioned in a chain (hole to hole), this can cause a buildup of error on a long bar.

Slots are great if you need some adjustment during assembly or thermal expansion.

Make sure that the hole size is correct for the bolt & washer you will be using. If the bar is plated, there will be a thin layer of coating added.

Holes are also where busbars are joined together. The overlap area, bolt size, washers & torque will all affect how well the joint conducts. Poorly made busbar joints will get hot and are one of the most common causes of panel failure. If there isn’t any information on the joints, ask.

5. Decode the Bends

This can be the trickiest part to read. Look out for:

  • Angle of bend (90 degrees, 45 degrees, etc.)

  • Direction of bend (edge bend or flat bend, up or down)

  • Inside Radius

  • Distance from the bend line to the nearest hole.

As a general rule, try and keep the holes a safe distance from the bend line. If they are too close to the bend, they can become distorted. If you have tight radii on a thick/hard temper bar, this can cause cracking. If your design requires a very tight bend, ask your manufacturer early on.

Twist & Z bends should be clearly shown in a sketch.

If you are unsure about the direction of the bend, look at the view. Flat bends (wide face folded over) are easy to do. Edge bends are harder on the material, so they should have a clear note.

6. Look at Tolerances

Tolerances tell the shop how much variation is acceptable. Most drawings will have a general tolerance (e.g., +/- 0.5 mm) and tighter tolerances on key features like hole pitch.

More isn’t always better. Each additional decimal place will cost more. Only add tighter tolerances if it is really necessary for the fit.

A good tip is to only add critical tolerances to dimensions that affect the fit or electrical contact.

7. Surface Treatment, Plating & Insulation

The surface treatment will affect the contact resistance and corrosion life. Common options are:

  • Tin Plating—A good all-round option. Often used on copper.

  • Silver Plating – Low contact resistance. Good for high current joints.

  • Nickel Plating – Hard wearing.

  • Insulation—PVC Sleeving, Heatshrink, or Epoxy Powder Coating.

The drawing should also show if the bar is fully plated or just at the joints. If the thickness of the plating is important, this should also be mentioned.

If you’re unsure what finish to go for, tell your manufacturer what environment the busbar will be in (indoors, outdoors, humid, or coastal) and the current rating. They can advise what is worth paying for.

As a general rule, tin-plated copper busbars are the usual all-round choice for indoor panels. If the busbar is in a harsher, hotter, or more corrosive environment, a nickel-plated copper busbar (sometimes referred to as a nickel busbar) will be chosen. Silver is saved for high current joints.

Where are these drawings used?

  • Switchgear and MCC/PCC Panels

  • Transformers and UPS

  • EV Charging and Battery Energy Storage

  • Solar Inverters and Combiner Systems

  • Data Centers and Industrial Automation

Also included in this category are EV busbars, lithium battery connector assemblies, and even simple items such as a 3-phase meter box with a busbar. Wherever there’s compact and organized power distribution, you’ll see custom bent busbars.

Copper or aluminum? What the Drawing Should Reflect

Copper is a much better conductor and is easier to plate and solder. It can be a heavier material and is often more expensive. However, it has a smaller cross-section and requires less care when soldering.

When changing the material, you will need to change the material note in the title block. The cross-section, hole size, bolt torque, and plating should also be checked.

Many manufacturers will provide you with both options side by side so you can see the difference in price.

This is why you will see a lot of searches for copper busbar current-carrying capacity and aluminum busbar current-carrying capacity. The same size will have different current carrying capacities. You will need to ensure what size and material you have on your drawing matches the current rating you require.

What is a busbar drawing?

A busbar drawing is a technical drawing that shows the size, hole positions, bends, material, plating, and tolerances of the busbar. This is used by manufacturers to create the part exactly as you have designed.

Advantages of a Well-Designed Busbar Drawing

  • Accurate quotations and reduced queries.

  • Fewer chances of rejection and rework.

  • Repeat orders will be consistent.

  • Better electrical performance and secure joints.

  • Faster lead times.

Challenges You’ll Run Into

  • No bend radius or bend allowances provided

  • Old versions of drawings

  • Tolerances are too tight, causing increased costs.

  • 2D drawings don’t show 3D complex shapes clearly.

If you have a 3D model (STEP file), please provide this along with your PDF.

These issues shouldn’t be a problem but will be much easier to resolve at this stage rather than in the workshop.

Expert Tips

  • Make sure to provide PDF and CAD (DWG/DXF/STEP) files.

  • Clearly indicate any critical dimensions.

  • Add brief notes about application and rating.

  • Specify if you want any inspections done, such as a first article report.

  • Ask for a DFM (Design for Manufacturing) check.

While it might seem like a small thing to do, having a one-page list of things to include on your drawings can become a habit for your whole design team.

A good bus bar design starts at the beginning, so provide the manufacturer with your layout early on. Often they will be able to make small suggestions to reduce the cost of your design (better bend radius, standard thickness, etc.) without affecting performance.

Common Mistakes People Make

  • Confusing flat length with finished length.

  • Not including bend radius.

  • Holes too close to bends/edges.

  • All tolerances are the same.

  • No temper or plating specification for material.

  • No revision number updated.

Most of these issues are based on assumptions. If it isn’t specified, then someone will assume it. This may not be what you intended.

How to Select a Custom Busbar Manufacturer in India

A manufacturer should be able to:

  • Work from your drawings. A good manufacturer will also point out any issues you may not have considered.

  • Use CNC punch, bend, and cut machines. Ideally with their own plating process or a dependable partner.

  • Use copper and aluminum materials. All materials should be traceable.

  • Quality checks, including measuring, plating thickness, and visual inspections.

  • Be able to produce samples and repeat orders.

  • Respond quickly to any technical questions.

A reliable copper busbar manufacturer will ask questions if there are any issues with your drawing. This is a positive thing!

It is also useful to request samples or examples of previous work. This will give you more information than a brochure.

When comparing busbar manufacturers in India, ensure they can do both copper and aluminum work. Whether you require copper busbar manufacturers in India or aluminum busbar manufacturers in India, it is usually best to have one supplier who can do both. This will ensure all your drawings, tolerances, and finishes are the same.

FAQs

1. How do I work out what size busbar I need for my panel?

Divide the current by the allowable current density for your material to give the required cross-sectional area. Choose a standard width and thickness. Ensure you check for temperature rise and your standard or ask your manufacturer to confirm.

2. What is the difference between flat length and finished length?

Flat length is the length of the strip before it has been bent. Finished length is the measurement after forming.

3. How near should a hole be to a bend? 

This will depend on the thickness and bend radius. Ask your manufacturer for the minimum distance for your design.

4. Can I send in a sketch?

 Yes, we can use this for quotations. However, it is much safer to provide a correct dimensioned drawing for production.

5. Should I use copper or aluminum busbars?

Copper provides greater conductivity and a more compact design. Aluminum will reduce weight and cost. It will depend on your current requirements and how much space you have.

6. What file types do manufacturers prefer?

PDF for reference and DWG, DXF, or STEP.

7. Should I use nickel or tin plating on copper bus bars?

Tin is the most common option. However, nickel-plated copper busbars are suitable for more extreme or hot environments. Choose based on your environment and current rating.

Wrapping It Up

Once you know where to look on the busbar drawing, you will find it easy to understand. You will want to check the title block, cross section, holes, bends, tolerances, and finish. If you get these right, you will rarely have any issues with production.

Having a clear drawing and a manufacturer who will read it will give you the quickest turnaround for your busbars.

If you want bespoke solutions, it is worth speaking to an experienced manufacturer. Companies like Adinath Enterprises will produce copper and aluminum busbars directly from your customer drawings. Send us your drawing for a review.

Contact Us

For any query, please call us, email us or fill the form and wewill contact you shortly.

+91-9899772424

+91-9899335858

abhinavjain2001@hotmail.com 

info@adinathenterprises.com

    About the author

    Leave a Reply